Placemat Envelope Clutch
You know you DIY too much when you look at a placemat and think of accessories...not food, tables or eating.
Supplies:
- Ruler
- Sharpie/marker
- Jewelry pliers
- Button of your choice. You can also use an old earring, pendant, etc.
- Wire cutters (depending on the button you're using)
- Magnetic purse closures (available in the sewing section of the craft store)
- Scissors
- E6000/super glue
- Flat button, or a button with a shank on the back (to be removed)
- Placemat
- Thick fabric, like vinyl or pleather. About 12x12 inches.
- Thiner fabric, like cotton or jersey. About 12x12 inches.
- Sewing machine & coordinating thread (not shown)
- Denim needle (for your sewing machine)
- Sewing pins
- Scrap paper
- White chalk or charcoal (might be useful)
I was going to use an elephant button, but changed my mind for a flat gold button that'd be easier to work with. Reason #32487648162 DIY is great: you can change your mind whenever you want.
For my additional fabrics, I used black pleather from Mood and black jersey from an old t-shirt.
Obviously, the final look of your clutch will depend on what kind of placemat you find. I'm sure Canada isn't the only place to find cool looking placemats, so try checking out stores like Home Goods, TJ Maxx, and Target. Your local dollar store is always worth a shot, though. Just make sure the placemat is thin enough to be sewn through two layers.
- White chalk or charcoal (might be useful)
I was going to use an elephant button, but changed my mind for a flat gold button that'd be easier to work with. Reason #32487648162 DIY is great: you can change your mind whenever you want.
For my additional fabrics, I used black pleather from Mood and black jersey from an old t-shirt.
Obviously, the final look of your clutch will depend on what kind of placemat you find. I'm sure Canada isn't the only place to find cool looking placemats, so try checking out stores like Home Goods, TJ Maxx, and Target. Your local dollar store is always worth a shot, though. Just make sure the placemat is thin enough to be sewn through two layers.
Closeup of the magnetic purse closures. They have prongs that can be bent in with pliers, to secure to fabric.
1) Fold the placemat in half, front sides facing each other. Draw a line on each side; you'll be sewing down these lines later on.
2) Place your placemat on a piece of paper. Find the midpoint, draw a line, and connect the top of this line to create a triangle like above. Make sure the "bottom" of the triangle has a good inch or so extra.
3) Cut out your pattern.
4) Place the pattern on one of the pieces of fabric, and measure an inch extra all around.
5) Cut out.
6) Repeat with the other piece of fabric.
7) Front sides facing each other, sew the two pieces together - EXCEPT for the bottom (not at the very edge, but right below the one inch marks. I didn't take a picture of this, so sorry!).
Flip it right side out, fold in the open ends of the bottom, and pin together. Sew this shut.
Flip it right side out, fold in the open ends of the bottom, and pin together. Sew this shut.
8) Pin the flap to one side of the placemat.
9) Sew the flap to the placemat.
Fold the placemat in half, right sides facing each other (just like you did in Step 1). Sew along those marker lines you drew, then turn the entire thing right side out.
Fold the placemat in half, right sides facing each other (just like you did in Step 1). Sew along those marker lines you drew, then turn the entire thing right side out.
10) Pierce two holes in the flap of the clutch. I'd recommend placing this on an old magazine, so as to not damage your table/desk/etc. Insert the prongs of one end of the magnetic purse closure, and bend in with pliers.
Repeat this on the placemat side, for the other end of the magnetic closure. Make sure they'll line up before making any holes (white charcoal or chalk might come into handy for marking lines to guide you when piercing holes).
Repeat this on the placemat side, for the other end of the magnetic closure. Make sure they'll line up before making any holes (white charcoal or chalk might come into handy for marking lines to guide you when piercing holes).
11) If needed, remove the back of the button.
12) Glue onto flap, covering up the prongs of the magnetic closure. Let dry.
Source: studs-and-pearls.com
0 nhận xét:
Đăng nhận xét